Welcome to the Knife Page!

We are building hand crafted QUALITY
knives to offer,  using only top line steels
and doing our own heat treat and tempering.
These are knives that you will have
to sharpen less because they will HOLD
that fresh edge for much longer!!!

Blades you can COUNT on!!!
We will custom harden/temper any of our
blades to customer requests.  We will advise
you in the case you request something that will
not be durable for either softness or excessive hardness!
*******************************
Our carbon tool steels are O1 steel with rare exception.
When you think O1, think router bits. 
VERY tough and exceptionally durable!
All of our Damascus steel is ground from billet and
properly heat treated in our forge!
**************************************
All our steel has lifetime warranty barring only if you want hard and
then use it to open a can of pork and beans at camp or if you let it rust.  ;)
All blades will be resharpened free for life to razor sharp for only the cost of postage!
Recommend washing and re-application of FrogLube after each use.
FrogLube is non-toxic, the best anti corrosion protection and FDA approved
for use on commercial meat slicing equipment!  All blades come with FrogLube
already applied!  Available in good gun stores across the country and on
on Ebay.  One drop on each side, wiped around does the job!  Hopefully,
all blades will soon be shipping with a small foil squeeze pack for trial.
FrogLuube is also GREAT for it's recommended use on firearms!

***************************************************************
Nine inch drop point Hunter.  Hardened and tempered 440C Stainless
This one is shaving sharp and will hold
a great edge for a long time!!!
$50.00 US
SOLD

**************************************************************

A very nice Damascus hunter!
512 layers of 1084 and 15N20
Damascus guard, blade and Zebrawood grips.
$85.00
SOLD

***********************************************************************

A bit smaller skinner Damascus blade.
This knife has Bloodwood grips and is
big enough to be useful, small enough to
be light and not get in the way.  This steel is made
by Brad Vice, Alabama Damascus steel!
Material = (4) layers 5160, (3) layers 203E, (3) layers 52100, (3) layers 15N20 folded 5 times for 416 layer damascus
About 57-58 Rockwell
$105
 
SOLD

*********************************************************

A very nicely finished skinner of 440C.  This one has a brass
finger guard on it with Zebrawood grips.
About 55 Rockwell.
$110.00
SOLD


***********************************************************

A very nice Damascus skinner with PakkaWood grips.
Very nice "heft" on this one and a nice pattern. 
Very nice knife!
56-57 Rockwell
$100.00
SOLD


***********************************************************

Great, durable hunter/skinner of 1084 high carbon steel.
Micarta (dyed canvas in resin) grips that are water and
chemical resistant and have a wonderful texture with
good grip! Tempured to approx 57-58 Rockwell.
 $70.00

Sold

************************************************************



Nice skinner with blue Pakawood scales and brass finger guard.
512 layer Damascus.  This one has some gorgeous patterns.
56-57 Rockwell

$110.00
SOLD

********************************************************************************************

Very nice clip point skinner.
512 layer Damascus.  Water buffalo scales.
56-57 Rockwell. 
$115.00


***************************************************************
A VERY hard and sharp O1 steel skinner.
tempered at 59 RHc, this baby will skin a bunch of
deer before needing any tuneup!  Dyed, stabilized
maple burl grips.
$175.00
SOLD

****************************************************************
O1 tool steel at 58 RHc.  Highly polished (gunstock finish)
black walnut grips, very comfortable!  Shaving sharp!
$145.00


**************************************************************
O1 tool steel skinner.  Maple burl grips, waxed.  58 RHc.
Very comfortable, very sharp!
$155.00
SOLD

***************************************************************
O1 tool steel skinner.  Maple burl grips, gunstock finish.  58 RHc.
Very comfortable, very sharp!

$165.00
Sold

****************************************************************
Small Damascus skinner.  Brad Vice damascus!
Black walnut grips with gunstock finish.
Material = (4) layers 5160, (3) layers 203E, (3) layers 52100, (3) layers 15N20 folded 5 times for 416 layer damascus
$125.00
Sold

**************************************************************
Page 2
More coming, page is subject to change frequently!
Check back if you don't see what you want, or contact us!






Copyright 2016  Chris Hayes
chris@stevespages.com